HOW TO INSTALL SURRON GRAPHICS

To complete the task, you'll need:

Heated garage (70°F or warmer).
Felt edge squeegee (optional)
70% isopropyl rubbing alcohol or soap/water.
Hobby knife (optional).
Hair dryer or heat gun (optional).
Time and patience.

Install Sheet Layout:

-Apply the wrap pieces in our recommended numerical order to help with artwork alignment.

Preliminary Notes:

-Our wraps are meticulously contour-cut to perfectly fit your unique machine, and are specifically designed for easy DIY application.

-Constructed with top-of-the-line 32 mil thick vinyl, digitally printed with high-quality self-adhesive backing, our wraps boast vivid colors, high resolution, and resistance to scratches and fading.

-Say goodbye to messy liquids during installation, as our wraps require a dry install for best results.

-If you're feeling unsure about the installation process, don't hesitate to seek assistance from a friend or someone experienced with vinyl applications. Your satisfaction is our priority.

Preliminary Notes:

-Our wraps are meticulously contour-cut to perfectly fit your unique machine, and are specifically designed for easy DIY application.
-Constructed with top-of-the-line 32 mil thick vinyl, digitally printed with high-quality self-adhesive backing, our wraps boast vivid colors, high resolution, and resistance to scratches and fading.
-Say goodbye to messy liquids during installation, as our wraps require a dry install for best results.
-If you're feeling unsure about the installation process, don't hesitate to seek assistance from a friend or someone experienced with vinyl applications. Your satisfaction is our priority.

Cleaning and Prep:

⦁ Begin by giving your machine a thorough wash with soap and water to get rid of grime, dust, dirt, mud, and other debris.
⦁ If your machine has any stock decals, we suggest removing them using direct sunlight or a heat gun for easier removal.
⦁ Use Rapid Remover or Goo-gone to get rid of any remaining adhesive residue.
⦁ Finish up with a final cleaning using 70% rubbing alcohol for a squeaky-clean surface.
** Avoid using oil-based products like WD40 & Pledge for cleaning your machine, as they can leave behind an oily residue that may negatively impact the adhesion of the wrap.

Install Steps:

⦁ Prepare the Vehicle and get it ready (Refer to the steps above)
⦁ Save or print out our Installation layout to easily locate all the pieces (Refer to the section above)
⦁ Maintain clean hands throughout the entire installation process for the best results.
⦁ Follow the numerical order on the sheet or start with the larger pieces for optimal outcome.
⦁ Gently peel and place your first piece, lightly securing one corner and adjusting the position as desired.
⦁ Utilize the Hinge technique (as shown in the images below) to secure the piece in place. Then, use your thumb to work from the center out on each side, removing air bubbles.
⦁ If you are satisfied with the placement, apply heat and pressure to activate the adhesive. If not, you can lift and reposition the piece.
⦁ Repeat these steps, aligning the artwork as accurately as possible from your last piece to the next.
⦁ Once all graphics are installed, use a heat gun or hair blower to go over the entire graphic and press down on the edges to ensure proper sealing. We recommend waiting 10-24 hours and repeating this step to ensure everything is securely in place. Note: Apply extra heat and pressure on textured plastics.
⦁ Trim any excess or overhanging edges of the graphic to prevent future lifting.
⦁ Allow your new graphics to cure for at least 10-24 hours before using the vehicle.

Disclaimer:

NextPicks is not liable for improper installation of graphics, damage to them due to improper install, or damage due to everyday abrasions. Our graphics are built with the highest quality materials and the decals hight-tac adhesive and heavy duty laminate will provide excellent adhesion, protection and longevity but that does not mean they are not indestructible.

Replacement Pieces:

If you require replacement parts, fret not! Simply drop us an email at numediabizz@gmail.com with photos highlighting the specific pieces you need, and we'll promptly provide you with a quote.
Do note that over time, color variations may occur due to changes in materials and equipment. However, we're here to help! We also offer a generous discount on full kit re-prints for your convenience.

POST YOUR WRAP ON SOCIAL MEDIA!